[1970-Jan-01 00:01:32.300652]: Loading settings from string...
[1970-Jan-01 00:01:32.600918]: Parsing toolhead settings for bronx...
[1970-Jan-01 00:01:32.646432]: Rebuilding toolhead structure
[1970-Jan-01 00:01:32.690875]: Building bronx location 0...
[1970-Jan-01 00:01:32.891300]: Initialization: heater settings
[1970-Jan-01 00:01:32.893186]: storing heater 0 to time out after 3 minutes at temp, 1 minutes with no rise of 10C, fan feedforward amount 15C
[1970-Jan-01 00:01:32.906313]: Settings: Parsing home subtree...
[1970-Jan-01 00:01:32.938449]: Init endstop for axis: 0, type: load_sense, polarity: false
[1970-Jan-01 00:01:32.950700]: Init endstop for axis: 1, type: load_sense, polarity: false
[1970-Jan-01 00:01:32.952523]: Init endstop for axis: 2, type: switch, polarity: true
[1970-Jan-01 00:01:32.980837]: Parsing root settings...
[1970-Jan-01 00:01:33.041070]: STEPPER CONVERSIONS: Axis 0 steps per mm: 88.5732
[1970-Jan-01 00:01:33.082283]: STEPPER CONVERSIONS: Axis 1 steps per mm: 88.5732
[1970-Jan-01 00:01:33.084138]: STEPPER CONVERSIONS: Axis 2 steps per mm: 400
[1970-Jan-01 00:01:33.085961]: STEPPER CONVERSIONS: Axis 3 steps per mm: 108.55
[1970-Jan-01 00:01:33.087922]: STEPPER CONVERSIONS: Axis 0 periods per second 71392.9 seconds per period 1.4007e-05 slowest tickrate axis 0 tickrate 1.4007e-05 radices 32 2 30 0
[1970-Jan-01 00:01:33.100415]: STEPPER CONVERSIONS: Axis 1 periods per second 71392.9 seconds per period 1.4007e-05 slowest tickrate axis 0 tickrate 1.4007e-05 radices 32 32 30 0
[1970-Jan-01 00:01:33.102669]: STEPPER CONVERSIONS: Axis 2 periods per second 71392.9 seconds per period 1.4007e-05 slowest tickrate axis 0 tickrate 1.4007e-05 radices 32 32 32 0
[1970-Jan-01 00:01:33.104853]: STEPPER CONVERSIONS: Axis 3 periods per second 17847.6 seconds per period 5.603e-05 slowest tickrate axis 3 tickrate 5.603e-05 radices 32 32 32 31
[1970-Jan-01 00:01:33.107281]: syncing set to true
[1970-Jan-01 00:01:33.160384]: Axis count unspecified, defaulting to 4
[1970-Jan-01 00:01:33.199349]: Loading capacitor model settings for extruder 0
[1970-Jan-01 00:01:33.213153]: Have 1 valid ToolheadManager pointers, 0 is 0x1df6d8
[1970-Jan-01 00:01:33.318602]: setting driver address to 22
[1970-Jan-01 00:01:36.680811]: Init step: 0
[1970-Jan-01 00:01:36.740847]: Reset Toolhead Program State
[1970-Jan-01 00:01:36.742512]: Toolhead programmer: Resetting
[1970-Jan-01 00:01:36.744283]: done
[1970-Jan-01 00:01:37.890804]: Init step: 1
[1970-Jan-01 00:01:37.897862]: done
[1970-Jan-01 00:01:38.383201]: Init step: 2
[1970-Jan-01 00:01:38.384969]: done
[1970-Jan-01 00:01:38.885246]: Init step: 3
[1970-Jan-01 00:01:39.040858]: done
[1970-Jan-01 00:01:39.404474]: Init step: 4
[1970-Jan-01 00:01:39.431368]: done
[1970-Jan-01 00:01:39.911916]: Init step: 5
[1970-Jan-01 00:01:39.940468]: done
[1970-Jan-01 00:01:40.420513]: Init step: 5
[1970-Jan-01 00:01:40.522586]: done
[1970-Jan-01 00:01:40.909470]: Init step: 5
[1970-Jan-01 00:01:40.990823]: done
[1970-Jan-01 00:01:41.422153]: Init step: 5
[1970-Jan-01 00:01:41.423929]: done
[1970-Jan-01 00:01:41.914821]: Init step: 5
[1970-Jan-01 00:01:41.921539]: done
[1970-Jan-01 00:01:42.416356]: Init step: 5
[1970-Jan-01 00:01:42.518415]: done
[1970-Jan-01 00:01:42.918075]: Init step: 5
[1970-Jan-01 00:01:42.931020]: Toolhead 0: Packet 0x0: Calculated CRC: 0x62f5481b  Packet CRC: 0x0
[1970-Jan-01 00:01:42.933069]: Toolhead 0 : Toolhead Response Fail with comm_error: 1  Retry # : 1
[1970-Jan-01 00:01:42.934768]: done
[1970-Jan-01 00:01:43.441418]: Init step: 5
[1970-Jan-01 00:01:43.443226]: done
[1970-Jan-01 00:01:43.938191]: Init step: 5
[1970-Jan-01 00:01:43.954444]: done
[1970-Jan-01 00:01:44.451016]: Init step: 5
[1970-Jan-01 00:01:44.553078]: done
[1970-Jan-01 00:01:44.942934]: Init step: 5
[1970-Jan-01 00:01:44.950949]: Got valid API version 6 for Toolhead 0
[1970-Jan-01 00:01:44.959685]: done
[1970-Jan-01 00:01:45.563879]: Init step: 5
[1970-Jan-01 00:01:45.570468]: done
[1970-Jan-01 00:01:46.065261]: Init step: 5
[1970-Jan-01 00:01:46.167364]: done
[1970-Jan-01 00:01:46.577536]: Init step: 5
[1970-Jan-01 00:01:46.590992]: Toolhead 0 state error: 80
[1970-Jan-01 00:01:46.593169]: Toolhead 0: Toolhead has Firmware version 1.7,736
[1970-Jan-01 00:01:46.595096]:  Toolhead 0 initialized
[1970-Jan-01 00:01:46.596811]: done
[1970-Jan-01 00:01:47.079423]: Init step: 6
[1970-Jan-01 00:01:47.091538]: done
[1970-Jan-01 00:01:47.581646]: Init step: 7
[1970-Jan-01 00:01:47.584185]: done
[1970-Jan-01 00:01:48.101347]: PRU Event: PRU_INIT
[1970-Jan-01 00:01:49.100995]: bronx lowest mem space: 0x376 bytes
[1970-Jan-01 00:01:49.102870]: Checking tool eeprom version
[1970-Jan-01 00:01:49.104519]: Commanding tool usage stat retrieve
[1970-Jan-01 00:01:49.106179]: New tool uid 0x143c6 attached, updating info cache
[1970-Jan-01 00:01:50.600962]: Connected tool has eepromv4
[1970-Jan-01 00:01:52.112324]: Raw usage stats: retract 391548456ct, extrusion 181796732 steps, 855675 seconds, refurbed 0 times
[1970-Jan-01 00:01:52.114107]: Steps/mm not configured, tool usage logging will be wrong!
[1970-Jan-01 00:02:15.580968]: bronx lowest mem space: 0x372 bytes
[1970-Jan-01 00:02:36.733679]: GetCachedToolUsageStats called
[1970-Jan-01 00:04:32.921222]: Toolhead 0 state error: 0
[1970-Jan-01 00:04:34.183535]: Heater manager Set Target Temperature to 215, index 0
[1970-Jan-01 00:04:34.185604]: Sent heater settings hold timeout 3min, rise timeout 1min, rise threshold 10C, sag threhsold 20C, overrun threshold 20C, fan preload 15C, preload tick delay 8900ticks, temperature freeze timeout 54464ms (may be discretized)
[1970-Jan-01 00:04:35.615677]: wait for heaters at target, wait bitmask 0x1
[1970-Jan-01 00:04:35.673742]: bronx lowest mem space: 0x352 bytes
[1970-Jan-01 00:07:25.322098]: libstepper: false toolhead: false( ignored: false) acceleration_manager: true
[1970-Jan-01 00:07:29.604470]: libstepper: false toolhead: false( ignored: false) acceleration_manager: true
[1970-Jan-01 00:07:33.815323]: libstepper: false toolhead: false( ignored: false) acceleration_manager: true
[1970-Jan-01 00:07:39.574900]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-01 00:07:43.946216]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-01 00:07:48.014752]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-01 00:07:52.138454]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-01 00:07:56.234865]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-01 00:08:00.549707]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-01 00:08:04.871078]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-01 00:08:04.934917]:  wait for axis 0 full: false offset: 126 l3map offset:    126 status: 1 position 0 status count 1001
[1970-Jan-01 00:08:09.536662]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-01 00:08:11.479260]: Raw HES proceeding
[1970-Jan-01 00:08:11.512748]: Got raw val 21442, saturated: false
[1970-Jan-01 00:08:11.543024]: Returning HES
[1970-Jan-01 00:08:11.544689]: Sending back val 21442, saturated false
[1970-Jan-01 00:08:11.655813]: TH0: 2 failures in last 465 packets (0.430108%)
[1970-Jan-01 00:08:11.657789]: Toolhead Abort
[1970-Jan-01 00:08:11.670478]: aborting pru with shutdown=true
[1970-Jan-01 00:08:11.680861]: Last sync period had (0,0,16638) buffer fulls due to suspend moves
[1970-Jan-01 00:08:11.682638]: Libstepper All Axis Abort
[1970-Jan-01 00:10:39.589810]: Toolhead 0 state error: 56
[1970-Jan-01 00:10:41.602116]: Toolhead 0 state error: 0
[1970-Jan-01 00:13:15.942814]: Heater manager Set Target Temperature to 215, index 0
[1970-Jan-01 00:13:15.944603]: Sent heater settings hold timeout 3min, rise timeout 1min, rise threshold 10C, sag threhsold 20C, overrun threshold 20C, fan preload 15C, preload tick delay 8900ticks, temperature freeze timeout 54464ms (may be discretized)
[1970-Jan-01 00:13:17.194414]: wait for heaters at target, wait bitmask 0x1
[1970-Jan-01 00:15:24.859563]: libstepper: false toolhead: false( ignored: false) acceleration_manager: true
[1970-Jan-01 00:15:29.231192]: libstepper: false toolhead: false( ignored: false) acceleration_manager: true
[1970-Jan-01 00:15:33.693798]: libstepper: false toolhead: false( ignored: false) acceleration_manager: true
[1970-Jan-01 00:15:39.092216]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-01 00:15:43.733979]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-01 00:15:47.941491]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-01 00:15:52.304433]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-01 00:15:56.293940]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-01 00:16:00.483903]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-01 00:16:04.845956]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-01 00:16:05.119327]:  wait for axis 0 full: false offset: 90 l3map offset:    90 status: 1 position 0 status count 1001
[1970-Jan-01 00:16:09.377788]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-01 00:16:11.624787]: Raw HES proceeding
[1970-Jan-01 00:16:11.662840]: Got raw val 22209, saturated: true
[1970-Jan-01 00:16:11.688289]: Returning HES
[1970-Jan-01 00:16:11.689974]: Sending back val 22209, saturated true
[1970-Jan-01 00:16:11.807163]: Toolhead Abort
[1970-Jan-01 00:16:11.808928]: aborting pru with shutdown=true
[1970-Jan-01 00:16:11.822112]: Last sync period had (0,0,31248) buffer fulls due to suspend moves
[1970-Jan-01 00:16:11.824053]: Libstepper All Axis Abort
[1970-Jan-01 00:16:19.709637]: Heater manager Set Target Temperature to 215, index 0
[1970-Jan-01 00:16:19.731809]: Sent heater settings hold timeout 3min, rise timeout 1min, rise threshold 10C, sag threhsold 20C, overrun threshold 20C, fan preload 15C, preload tick delay 8900ticks, temperature freeze timeout 54464ms (may be discretized)
[1970-Jan-01 00:16:21.014005]: wait for heaters at target, wait bitmask 0x1
[1970-Jan-01 00:16:34.074171]: Steps overrun! last 65130 and just got 10449
[1970-Jan-01 00:16:34.075889]: calculated 10854
[1970-Jan-01 00:16:40.471637]: libstepper: false toolhead: false( ignored: false) acceleration_manager: true
[1970-Jan-01 00:16:44.447492]: libstepper: false toolhead: false( ignored: false) acceleration_manager: true
[1970-Jan-01 00:16:48.786141]: libstepper: false toolhead: false( ignored: false) acceleration_manager: true
[1970-Jan-01 00:16:53.024573]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-01 00:16:56.902045]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-01 00:17:01.184003]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-01 00:17:05.120358]: libstepper: false toolhead: true( ignored: false) acceleration_manager: true
[1970-Jan-01 00:17:08.246295]: Toolhead 0 state error: 65
[1970-Jan-01 00:17:10.312322]: Raw HES proceeding
[1970-Jan-01 00:17:10.494368]: HES not updated!
[1970-Jan-01 00:17:10.552207]: HES not updated!
[1970-Jan-01 00:17:10.597867]: HES not updated!
[1970-Jan-01 00:17:10.658686]: HES not updated!
[1970-Jan-01 00:17:10.690983]: Got raw val 22553, saturated: true
[1970-Jan-01 00:17:10.717295]: Returning HES
[1970-Jan-01 00:17:10.719807]: Sending back val 22553, saturated true
[1970-Jan-01 00:17:10.810885]: Toolhead Abort
[1970-Jan-01 00:17:10.812664]: aborting pru with shutdown=true
[1970-Jan-01 00:17:10.816210]: Last sync period had (0,0,34797) buffer fulls due to suspend moves
[1970-Jan-01 00:17:10.818000]: Libstepper All Axis Abort
[1970-Jan-01 00:17:16.972080]: Raw HES proceeding
[1970-Jan-01 00:17:17.096069]: HES not updated!
[1970-Jan-01 00:17:17.141727]: Got raw val 22553, saturated: true
[1970-Jan-01 00:17:17.166979]: Returning HES
[1970-Jan-01 00:17:17.168661]: Sending back val 22553, saturated true
[1970-Jan-01 00:17:17.264529]: Toolhead Abort
[1970-Jan-01 00:17:17.266302]: aborting pru with shutdown=true
[1970-Jan-01 00:17:17.282637]: Last sync period had (0,0,34860) buffer fulls due to suspend moves
[1970-Jan-01 00:17:17.284399]: Libstepper All Axis Abort
[1970-Jan-01 00:17:24.773752]: Heater manager Set Target Temperature to 0, index 0
[1970-Jan-01 00:17:24.775523]: Sent heater settings hold timeout 3min, rise timeout 1min, rise threshold 10C, sag threhsold 20C, overrun threshold 20C, fan preload 15C, preload tick delay 8900ticks, temperature freeze timeout 54464ms (may be discretized)
[1970-Jan-01 00:17:32.336562]: Toolhead 0 state error: 54
[1970-Jan-01 00:17:32.338304]: Tool UID becomes 0.